깝스토리 업체지원센터

How to Go About boarding up commercial property boarding up companies a Door

A door can be boarded up as one way to protect vacant investment properties from the elements. It may not prevent all damage however it can help to avoid some of the problems associated with severe storms.

The idea of boarding up doors and windows can also deter burglars and vandals as well as squatters. However, it can be expensive and time-consuming to set up plywood boards over the openings of a property.

Measure the Door

You'll first require a tape measurement. It is a good idea to keep a chair or ladder close by in case you require to see more clearly the top of the frame. Wear gloves and goggles if you have to make use of these tools.

Begin by taking measurements of the door's width. This can be accomplished by running the tape horizontally across the door. Be sure to remove all additional parts of the door, for instance a sweep, when measuring. Then, measure the height by measuring from the floor to the sill or the lintel. It is essential to measure in multiple locations, particularly when measuring doors that are older as they may not be a perfect rectangular shape. If the measurements differ, use the largest figure.

After you've recorded the measurements of height and width and boarding up doors you'll need to figure out what size board you'll need for the frame. It should be at least 2'' wider and 1 inch taller than the door. 2'' higher. This will give you plenty of room to shim the frame and door to fit.

It's a good idea to remove the casing or trim around the jambs of the door in order to see the studs. This will allow you to take measurements of the exact gap between the frame's studs and the edge.

After you have removed the trim, measure the width of your door frame using a tape measure. Measure the frame at three different places and use the smallest measurement. You should also determine the height of the frame from top to bottom on both sides. Use the shortest measurement to determine the width of your door.

If you're having issues with these measurements it's best at this point to consult an expert and ask them to come out to your house to do the measuring for you. They'll tell you the size and type of door you require and how to prepare your frame for a new door.

Cut the Plywood

A door frame is typically comprised of studs or thin boards that create a hollow space around the door. The typical door is secured by two hinges connected to the studs. If you wish to refinish the door, you'll have to take it off its hinges over night. Placing plywood into the door's opening is a simple way to board the door and keep insects from gaining entry into the home. It's easy to do this without nailing or screw the plywood to the door's frame.

Plywood is cheap, easy to work with and looks fantastic when finished. It is the perfect material to use as a temporary solution to a problem in which you need to remove the door you have in place to finish it or build the new one. It is also useful for securing the opening in the room being renovated, such as an unfinished basement or a construction site.

Start by taking measurements of the width of the door opening and the height. Draw the dimensions on the plywood using the help of a utility knife, a drywall square or another straight edge made of metal. Then, you should snap a chalk line across all the marked lines to mark the areas you want to cut. Finally you can use circular saws to cut the plywood to the desired size.

It is crucial to protect both your eyes and ears when cutting plywood. Wear protective goggles or earplugs when you can. Additionally, it is essential to choose a blade that has a wide range of teeth that can cut quickly and with less tear-out. To avoid breaking pieces of wood from the edges of your cut, use a small block of wood as template to guide the blade and hold it just a hair's width away from the line when cutting.

Attaching a pair or short braces at each end is a good way to secure the plywood in place, without putting screws into the studs. Put one brace inside and the other on the outside of the door. Install a deck screws in each hole, and then tighten by using an open-end ratchet.

Secure the Plywood

It's time to attach the frame to the panel once you have the plywood sheet cut to the correct size and the holes to attach the rails and stiles of the door frame are predrilled. This is a relatively simple project that does not require any extensive carpentry skills so long as you follow the right procedures and use the proper tools.

Begin by setting emergency boarding up cost a table near the doorway. There are two sawhorses and 2-by-4 framing lumber at each end of the table. Lay the entire sheet of plywood flat on top of the sawhorses using the marks left by the measurement process to guide you to cut. Utilize a utility knife and a straight edge of metal to score the lines. This will create an outline for the saw blade, and will help to prevent splintering during cutting the plywood.

Wear eye protection and use a circular or table saw with a blade that has a fine-toothed edge to cut along the line of scoring. Sand the edges of the panels with 120-grit paper to smooth it out and eliminate any burrs. After sanding the plywood panels apply a wood sealer and allow it to dry according to the instructions of the manufacturer.

Install the hinges on the door frame. If you're using a hinge with a T-hinge make holes in the exterior side of your door to accommodate the strap portion of the hinges. Then, screw the hinge's outside edge to the frame using the screwdriver. Repeat the process for each hinge on the inside of your door. Be careful not to tighten them too much or the door could move.

If you have only a single hinged outside door, you can make it easier for the latch to close by fishing a wire through the loops of the outside hinges. Fold a piece of make a half-way tie, and then thread it through the two holes on the exterior of the door. Then, twist the wires and fix the door.

Install the Plywood

With the measurements you made using the measurements you took, put the plywood in the door opening. Adjust the header (top) of the frame and the sill (bottom). Use a level to ensure that there is no slop between the header and sill. If the level isn't perfect, put another shim where is required and repeat the process until you get the header and sill to be in a straight line.

Once the plywood has been put in place, secure it with the stainless steel hinge bolts and wingnuts. Use a screwgun equipped with an attachment for a hex head to avoid stripping off the screws' heads.

If you live in a house boarding up service with studs running the length of your doorway, you could drill hanger bolts into each framing member. This is much simpler than using a drywall saw to create the hole.

After putting the plywood in place after installation, take measurements of the width and the height of your door opening. If needed, trim the bottom of the plywood to fit the height of your door frame. Cut two pieces of framing lumber 1 by 6 as braces for the lower and upper ends. Put on eye protection and cut along the lines marked on the plywood using a circular saw fitted with a fine-toothed knife. Get rid of any splinters that may have formed in the cuts with an sanding block.

After you have placed the braces, use two pairs of finishing nails that measure 2 inches to join each brace to the plywood. After you're done counter-sink the heads of all nails. Seal the braces and the plywood with a high-quality wood sealer, such as this wipe-on polyurethane from Minwax.

If the door is too large for your doorway, you could add some decorative molding to fill in the space between the door and jamb or resize the opening. In many cases, however it is less expensive and simpler to purchase a new door. It also removes any problems you might have encountered with your door's original model even if it was damaged or was not fit for the opening.