UPVC Window Handle glass replacement windows

It is easy to replace a broken window handle with the proper tools. It's important to know the type of handle you have as well as the size of its spindle before you purchase an alternative.

Older uPVC window handles have a spur which protrudes and locks over the wedge striker for cockspur. These can be either right or left-handed and have to match when replacing.

What kind of lock and handle do I need?

There are many window locks and handles made from upvc, each with its own advantages and purposes. The type of handle you are using will determine how easy it is to open your windows and whether or not the locking mechanism functions as intended. With time and regular use, window handles made of upvc can become damaged or worn out, rendering them less secure and effective. In some instances they might even be completely removed. It is important to repair the handles on your window made of upvc immediately if you notice they are falling off. This will stop possible burglaries and ensure that your home is secure.

The good news is that replacing your upvc window handles is a relatively simple task that is achievable by nearly anyone. You'll require some basic tools, but with the right knowledge, it is a straightforward process that should take only a couple of minutes. To begin you must determine the type of lock and handle that you have on your upvc window and then identify the best replacement.

Inline Espagnolette Handles

These are the most common type of upvc handle and are typically located on the outside of your window. They are flat and feature an open latch that is connected to the locking mechanism of the window frame. Inline upvc handles have a spindle that runs through the center of the handle and then into the frame of the Window Seal replacement (ani114.com) to operate the latch.

Cockspur Handles

These handles are typically found on older uPVC windows and feature an distinctive hook-shaped design. Cockspur handles are held to the frame of the window with only one screw and are less secure than other types of window handles.

Tilt and Turn Handles

As opposed to the other handles made of upvc that are tilt and turn, these handles can both be rotated to open the window and the handle can be tilted to the side to allow ventilation. They have a 7mm spindle in the back and are available in left and right-handed versions.

When you are purchasing replacement handles for upvc it is essential to check the spindle length because not all handles are identical in size. Drop something into the middle of the hole to measure the length. This is the maximum spindle size that will fit in your windows.

What is spindles?

uPVC window handles operate similarly like doors, turning the handle to open an opening inside the frame. This unlocks the window so that it can be shut and opened. The handles can become damaged, especially if they're often used or are subjected to harsh conditions. This can leave you needing to replace your uPVC handles for windows as they might not be able to operate the window in a proper manner for a long time.

There are several different types of uPVC handles available comprising Espag, Cockspur and Spaded handles. These handles are designed in a variety of ways to fit into uPVC frames. Each handle type uses an individual spindle to lock the window mechanism. This is why it is crucial to know what kind of handle you have installed on your uPVC window so you can find the right replacement.

The base of the handle will tell you what type of uPVC it is. There should be a'snap in cover over one screw which holds the handle base in the correct position. Remove this and then you should be able see the second screw on the opposite side of the base of the handle. Once both screws have been removed and you are able to remove the handle from the uPVC.

After removing the uPVC handle, remove it from the locking mechanism. Note the length of the spindle. You will need to buy a replacement of the same length as the original handle and locking device.

The most common issue with window handle problems with uPVC is that the spindle becomes worn out and can no longer operate the locking mechanism. This can be caused by corrosion, damage due to constant use or the locking mechanism becoming looser. When this happens it is necessary to replace the window handle as well as the locking mechanism to restore the full functionality to your uPVC windows.

How do I remove my old handle?

Window handles can become damaged or even broken over the course of time. It is essential to fix them as soon as you can to ensure your safety. It is easy to replace a worn or damaged handle. The task can be completed in less than a minute without the need for special tools.

To take off the handle, first remove the screw that is located at the base of the handle. After this screw is removed, the handle can then be pulled away from the base. A second screw is situated at the base of the handle. This too can be removed. Once both of these screws are removed, the handle can be removed completely from the base of the window.

After the handle has been removed, grab the new handle and line up the fixing holes with the holes present in the window frame. If there is a cap or window seal replacement sticker on the new handle remove it if needed and screw the handle into place. Once the handle is set, it is essential to check that it works by turning the handle and making sure that the lock mechanism is activated.

Espag handles have an extra spindle that is protruding from the handle and slot into a multipoint locking mechanism within the frame of the window. Cadenza windows have blades with cut-outs that slot into the lock mechanism while Cockspur handles have a long nose that hooks over either the outer frame or transom bar cross member in the window.

Once you have the new handle in place, insert the spindle inside the lock in the window and then tighten it. Replace the snap-in cover and screw cap (if appropriate) once the handle has been firmly fixed. The handle is now ready to use by opening and closing the window several times to check that it functions well and securely.

How do I install the new handle?

It's not difficult to change the handle on your Upvc windows. The process is easy. All you require is a screwdriver and a small amount of patience. The first step is ensure that the handle you have previously used is not locked and then remove any screws that are visible, you can replace them by screw caps if you need. Once the handle is removed, you need to make an outline of the length of the spindle that extends from the back of the handle. This is crucial since it will determine the kind of handle that you will need to buy.

Espagnolette handles are the most common type of handle used on uPVC windows. The spindle is inserted into the handle to operate the locking mechanism within the frame of the window. The handle releases the latch, allowing the window to open. In regular use and over time, handles made of espagnolette can be damaged.

Cadenza handles are a form of uPVC handle that is commonly employed with tilt and turn windows. They feature a protruding knife that operates a multiple-point locking mechanism inside the window. They are usually more secure than handles made of espagnolette because they can only be opened from the inside. You can replace them with the same method that you would for espagnolette handles, but make sure the new handle is not angled and flat.

After you have picked the right handle, simply align the new handle with the existing screw holes prior to screwing it in place. After that, you should put the screw covers back on and make sure your new handle is operating correctly. This is done by moving the handle from locked position to the unlocked and then back to the locked position several times. It may be worth contacting an expert to determine if you can resolve any issues. They can advise you on how to solve the problem in a timely and effective way.