UPVC Window Handle Replacement

It's simple to repair a broken window handle with the right tools. But it's essential to know the type of handle and its spindle's length prior to purchasing the replacement.

Older uPVC window handles have a spur that protrudes and locks on the wedge striker for cockspur. They can be left- or right-handed, and must match when replaced.

What type of lock and handle do I have?

There are many different types of window handles made from upvc and locks, each with its distinct advantages and functions. The type of handle you choose will determine if the locking mechanism you have is effective and if it is easy to open windows. As time passes, and with regular use the upvc handles that are on your windows could become damaged and worn out. This makes them less secure and effective. In some cases they might even disappear completely. It is essential to fix your upvc window handles when you notice them falling off. This will help prevent burglaries, and keep your house secure.

The good news is that replacing your upvc window handles is a fairly simple job that can be done by everyone. You'll require a few basic tools, but with proper knowledge, it's an easy task that will only take a couple of minutes. You must be aware of the type of lock or handle you have on your window. This will help you select the correct replacement handles for upvc windows.

Inline Espagnolette Handles

These are the most common type of upvc handle and are typically located on the other side of your window. They are flat in design and come with a latch that engages with the locking mechanism on the window frame when turned. Inline upvc handles come with a spindle running through the middle of the handle and into the window frame in order to control the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames and have a distinctive, hook-shaped design. Cockspur handles are held to the window frame by one screw, and are less secure than other varieties of window handles.

Tilt and Turn Handles

As opposed to the other upvc handles that are tilt and turn, these handles can both be rotated to open the window, and the handle can be tilted to the side for ventilation. In general, they have a 7mm spindle on the back of the handle and are available in left and right handed versions.

It is essential to know the size of the spindle when purchasing a replacement upvc handle. There are a few that are exactly the same size. Drop something in the middle of the hole to test the length. This is the length of the spindle that will fit in your window.

What is a spindle?

uPVC window handles work similarly as doors, with the user turning the handle to activate an internal latch within the frame. The latch opens the window, so it can be shut and opened. However, sometimes the handles may become damaged, particularly when they are frequently used or exposed to harsh weather conditions. This could mean that you have to replace your uPVC handles on windows since they may not operate the window properly anymore.

There are many types of uPVC handle options, including Espag, Cockspur, and Spaded handles. These handles are made in a variety of ways to fit into uPVC frames. Each handle style uses an entirely different spindle for locking the window mechanism. It is essential to determine the kind of handle that is installed on your uPVC windows to ensure that you replace it with the correct one.

You can determine the type of uPVC handle you have by taking a look at the base of the handle. A snap-in covers should be over the screw that holds the base of the handle in place. Take it off and you should be able to see the second holding screw on the opposite side of the base section of the handle. After both screws are removed you should be in a position to pull the handle away from the uPVC window.

After removing the uPVC handle, carefully remove it from the locking mechanism. Take note of the length of the spindle. You'll need purchase a new one that is the same length as the original handle and the locking device.

The most common issue with uPVC window handle problems is that the spindle becomes worn out and can no longer operate the locking mechanism. This can be caused by corrosion, damage from constant use or the locking mechanism becoming looser. If this happens, it is required to replace the window handle and the locking mechanism to restore full functionality to your uPVC windows.

How do I take off the old handle?

Window handles can become damaged or broken over time. It is essential to repair them as quickly as possible to ensure your safety. It is simple to replace a worn or damaged handle. The job can be accomplished in under an hour without the need for special tools.

To take off the handle, you must first remove the screw at the bottom of the handle. After the screw is removed, the handle can be pulled away. Another screw will be located at the bottom of the handle. It can also be removed. Once these two screws have been removed, the handle will be detached from the base of the window.

After removing the old handle and align the fixing holes of the new handle to the existing holes in the window frame. If there is a cap or sticker on the new handle remove it if necessary and then screw the handle into place. It is crucial to verify that the handle is working after it is installed. Turn the handle and ensure that the lock mechanism is activated.

Espag handles come with an elongated spindle that extends from the handle and slots into a multipoint locking mechanism in the window frame. Cadenza windows feature a blade with cutouts that are incorporated into the lock mechanism. Cockspur handles are long and are hung over the outer frame of the window or the transom crossmember of the bar.

After you have put in the new handle, place the spindle into the window lock and tighten it. replace upvc window handle the snap-in cover and screw cap (if appropriate) after the handle is fixed. Once the handle is ready for use, open and UPVC Window Handle Replacement close the window a couple of times to ensure it works properly and securely.

How do I install the new handle?

Switching your uPVC window handle isn't difficult and the process is actually very simple. All you need is a screwdriver and a small amount of patience. First, make sure that the handle that you are replacing is unlocked. Then, remove any screws visible. You can also replace them using screw caps. After removing the handle and you are ready to take a note of the length of the spindle that extends from the back of the handle. This is crucial since it will determine the kind of handle that you will require to purchase.

Espagnolette handles are the most commonly used kind of handle that is used on uPVC windows. The spindle runs through the handle to activate the locking mechanism in the frame of the window. The handle releases the latch and allows the window to open. With time and regular use, espagnolette handles may become damaged or impaired, making it necessary to find an alternative.

Cadenza handles are a type of uPVC handle that is usually used with tilt and turn windows. They feature a protruding knife that operates a multiple-point locking mechanism inside the window. They are generally more secure than espagnolette handles as they can only be opened from the inside. You can replace them using the same procedure as you would for espagnolette handles, but make sure the new handle is not angled and flat.

Once you have determined the right handle for you You can simply align the new handle with the existing screw holes, and then screw it in place. Then, put the screws on and test your new handle. You can do this by moving the handle back and forth from the locked position to the unlocked one several times. If you have any issues, it may be worthwhile contacting a professional to determine if they can assist in resolving the issue. They can often advise you on the best approach to solve the issue in a quick and efficient manner.