Cat flaps allow your pet to leave and come at their own pace without needing to let them in or out. They can also help prevent your cat from urinating inside the home.

It is much easier to put a cat flap on a Upvc panel than on a glass one but you'll require some expertise and correct tools.

Take a measurement of the door

Installing a cat flap on a door can be tricky but if you select the right kind of cat flap, take your time and follow the steps provided it should not prove to be too much trouble. We will help you draw the shape and then use an jigsaw to cut out the door area. Then we'll complete the job by attaching the cat flap. This will ensure the flap stays in position and protects the doors from the damage caused by rain and wind.

To determine the size of the cat flap you require, take a measurement of your pet's width. This will ensure that the flap is large enough to let your pet leave and enter the home without having to open or close the door Fitting cat flap in upvc door Panel each time, yet small enough to prevent the pet from straying too far in either direction.

If your kit has an illustration of where to drill, then put it on the door and then use a pencil around it. If your door has a sill or moulding on the bottom edge then make sure you have enough clearance from these to ensure your cat's safety and will prevent them from getting access to your home.

Then put on your eye protection and dust mask and using a jigsaw begin cutting along the line that you have pencilled in, but don't push the blade too hard because this will make it cut faster than you want it to. Utilize a set square to ensure you are cutting the material properly and that the cut is a rectangle. When you are happy with the result, you are able to take out the rest of the door material.

Draw a Line

The cat flap is a great method to let your pet in and out without worrying about them coming in with a visitor, or leaving unwelcome gifts in the house. It also prevents draughts, and helps to keep your home's temperature stable. Fitting a cat flap cover for winter flap to your door may seem daunting to those who haven't done it before. A lot of people will hire an expert joiner or carpenter to do the work. This is an option but you can do it yourself, provided the tools are right and the steps are followed.

This is much simpler to do with a wooden door, but it is still possible using uPVC. However, you must be careful not to harm the doors as this could invalidate your guarantee. First, you must take measurements of the door to ensure that it can accommodate the new cat-flap. If you have an ordinary uPVC panel, this should be easy. However in the case of made of composite or another kind of door, you may require more care.

The next step is to measure the height of your cat's stomach. This is the height from the floor to the lower part of the cat's stomach and you'll need find a spot in the door where this measurement will fall within the range that your pet can comfortably go through. Once you've figured out the measurements you'll need to mark the area with a spirit level and a pencil so you are sure that the hole will be suitable for your cat.

Once you've marked the area, you're now ready to cut the hole. It is crucial to be patient and use a jigsaw to ensure the cuts are clean and smooth, not rough and uneven. This could cause damage to your door. Wear safety glasses and a dust mask while working with a jigsaw. Inhaling sawdust is hazardous for your health. Once you've finished cutting the hole, you will require sandpaper for smoothing the edges so that the cat flap is easily fitted into place.

Cut a Hole

Installing a cat flap to an existing door panel or double glazing sealed unit can be quite difficult. You may be tempted to tackle the job yourself, but unless have plenty of expertise in DIY, it's recommended to hire a professional in to do the job for you. A shoddy job might not only look ugly, but also an issue for security as well as allowing cold air to enter when the cat is outside and hot air to escape inside.

The hole's location should be marked on the door with an eraser and a spirit level. This will ensure it is properly positioned and is flush with the door's other parts. You should make sure you have some sandpaper on hand for any rough edges.

Once the line has been marked you should cut out the hole with the jigsaw. Remember to wear any necessary safety equipment for working with an electric tool. If you are worried about the noise of a jigsaw you can buy a cordless version which is quieter and more user-friendly to use.

It is best to only remove the material required to fit the cat flap. It is essential to leave some extra material to make the wall thickness of the cat flap. However cutting away too much could cause issues or even damage to the door frame.

If the door is made of upvc and has a metal panel or frame, it may interfere with the microchip flap. In this case you'll need create an over-sized hole to ensure that the metal doesn't get in contact with the walls of the flap.

If you are fitting an animal flap to an upvc door or a double glazed windows with a metal frame then you will need to speak to a specialist who can provide you with a new glass pane that already has the hole for the cat flap premade in it. This will be cheaper than trying to fit a cat flap in an existing pane that wasn't designed for this purpose.

Install the Flap

Cat flaps give your pet the freedom to go and come anytime they want and allow them to be comfortable in the house when they want to. However, if you own an uPVC door it can be difficult to fit a cat flap, particularly if you don't own glass panes that can be cut to fit one. If you're looking to install a half-glazed uPVC replacement upvc door panels with cat flap panel, it is possible to add the window cat flap flap. It's not just a matter of cutting holes in the door. You'll also have to take a few steps to ensure it's safe.

A composite, uPVC or GRP door panel is usually made up of a thin plastic skin that is attached to an insulating polystyrene core. The material is extremely fragile and care should be taken when cutting into it to avoid causing damage. This type of door usually includes a template that you can use as a reference to cut the hole in your door.

After you have marked out the opening in your front door, it's time to install the cat flap. You can pick from a range of designs, from simple push-button units to microchip-activated ones that allow only your pet to enter. However, no matter what kind of cat flap you select, it's crucial to ensure that your cat can use the flap without getting trapped outside in bad weather.

It's a good idea select a circular fitting cat flap in upvc door Panel (www.metooo.it) rather than a square one, as circles can be more securely cut into the door glass. It's because square holes are more likely to crack the glass when drilled. It's also a safer choice to use since you're not at risk of drilling into toughened glass that could shatter and injure your pet or your family. This is especially important if you have young or elderly person in your home who could be hurt by shards of glass.