UPVC Replacement Door Handles

Over time, the handles on your doors will wear down and need to be changed. It is crucial to be able to match the dimensions of the handles that were previously used when replacing them.

The top screw's position the lever, and the keyhole dimensions are the three measurements you have to verify. Check the size guide for help with this.

Inline Lever/Lever

A lever conservatory door handles handle is a modern handle that can be used on replacement or new doors. This style of handle is available in various designs and finishes. A number of manufacturers make this handle, including Avocet ERA, Fullex, Hoppe, Mila, Millenco & Yale.

Fab and Fix Windsor Inline Sprung Lever Door aluminium window handle

The handles made of uPVC/Composite are made from durable materials, and are perfect for multi-point lock doors that require a robust design. The handles are inline and run off the same spindle and screw fixings. They can be easily incorporated into new or existing uPVC/Composite doors.

The design of the sprung lever allows the handle to be set and angled to ensure a comfortable experience and is suitable for all users. The handle has been tested to 200,000 cycles, which allows for the assurance of the quality of the finish and the performance of the handle over time. The sprung lever can be cut to fit the widest range of locks. This is particularly useful for doors with narrower frames, where the cylinder is located further back. A lever that is shorter can be used for doors with a latch which can be operated with the thumb located on the inside.

Lever Pad

The lever pad upvc handle is different from the lever window handles for upvc used on the majority of doors. These handle types are either operated by one spindle, or two spindles, either inline or offset. They are typically utilized on UPVC doors with double glazing. They come in a range of finishes and variations.

The handles are available in various finishes, including White chrome, and Gold. The finish is BS EN 1670 Grade 5 and is resistant to corrosion. This gives the handle an outstanding performance and long-lasting durability for the purpose it was designed for.

All of the UPVC lever pad designs are supplied with the spindle and screws which allow them to be fitted on any new or existing uPVC door. The backplate fixing centres of 211mm allow for a wider size handle that is often a benefit when replacing a window handle a faulty or worn multi-point door lock mechanism. The handle levers come with springs, which eliminate the problem of door handles that move out of their horizontal position when not in use.

It is essential to match the dimensions of the PZ for both the multipoint lock as well as the uPVC doors when choosing the replacement UPVC spindle and handle. This measurement is often referred to as the 'handle centre' or 'cylinder centres' and is a critical aspect to match the appropriate handles.

Once you have the correct PZ size, you'll need to ensure that the lever pads and push pads are of a appropriate shape to accommodate the American with Disabilities Act (ADA) compatible handles you require for your doors. They typically have a square or round shape, with an internal lever and an external push pad.

The majority of the UPVC Lever Pads we sell are sprung. This means they can be reverted to a horizontal state when they are not in use instead of hanging and possibly sticking in the frame. This prevents draughts from entering the building. You will also find that the majority of UPVC lever pad handles are handed which allows you to place them on either side of the door.

Euro Cylinder

Cylinder locks are found on uPVC and other kinds of doors. They operate by using a key that unlock a cylinder case which then reveals pins which can be aligned with the pins in the lock body, allowing them to turn an revolving cam, opening the door. Euro Cylinders are available with up to six pins. External and internal doors require different levels of security.

Selecting the right cylinder for your needs is essential; it depends on how your doors and handles are utilized. For example, external doors must be secured with a higher security cylinder, while doors inside can be secured with a standard cylinder. Additionally, certain cylinders are available with extra features that can improve security even more, like anti-drill or anti-bump properties.

To make sure that the euro cylinder is of the right size for your door, it must be measured correctly. The cylinder should be measured from the hole in the center of the fixing screw to the end of the cylinder and the thumb turn if you have one. It is best to do this with the lock in place however, in the event that this is not feasible, you can take it off and remove it to take measurements. It is essential to ensure that there is no cylinder that extends beyond the handle or escutcheon. This can make it susceptible to lock snapping attacks.

The design of the latest cylinders includes anti-drilling and bump resistance features. They are designed to decrease the chances of an attack by causing the cylinder to rotate in the opposite direction. This helps prevent attacks and ensure your doors are secure.

There are cylinders that are made to withstand snapping. This is a more frequent method of attack on cylinders where the break line inside the lock is targeted with a special tool to break off the front of the cylinder and allow the door to open. This is a much faster and easier way to gain access than using a multipoint locking system. It also leaves no evidence of the break-in which can make it difficult to prove insurance claims.

Spring Cassette

The spring cassette is situated within the base plate of your door [Redirect Only] handle. It provides a sprung solution to help return the multipoint lock handles to their normal position after use. These handles used to have no spring and would droop when the locking mechanism was disengaged. Adding this simple component is one of the best ways to correct this issue and is an excellent way to stop your upvc doors from getting stuck in an open or closed position, as they aren't always simple to close manually.

These spring cassettes were designed to be used with a sprung multipoint lock. They will not fit handles that are not sprung and you'll have to cut a hole into your backplate for them to fit. (Please look at the image for a detailed diagram). These cassettes are a replacement to broken or missing cassettes that are in the backplate of uPVC door handles. They are sold as a single unit. They feature a square cut out that is able to accommodate an 8mm shaft.

These spring cassettes are a great value solution to the issue of sagging door handles. These spring cassettes are simple to install and will increase the life of your uPVC door. For more information on our selection of replace upvc window handle accessories and spares, contact us today. in contact with our team. We are on hand to assist you and offer expert advice.